allowable error造句
例句與造句
- Thermic electromotive force and allowable error at 200 mv
200熱電動勢及允差mv - Thermic electromotive force and allowable error at 100 mv
100熱電動勢及允差mv - Allowable error for judge of quality testing results in feeds
飼料檢測結果判定的允許誤差 - 1 . thermic electromotive force and allowable error
1 .熱電動勢及允差值 - Analysis of error sensitivity and allowable error of optical film , and computer controll in production
光學薄膜的誤差允差分析及生產過程中的計算機控制 - It's difficult to find allowable error in a sentence. 用allowable error造句挺難的
- The best parameters , precision grades and allowable errors of the transmission parts can be obtained by optimization to let the actuators meet the performance , technology and economy requirements simultaneously
根據傳動精度指標，最佳地規定和分配各傳動零件參數、精度等級及公差值，使之滿足設計、工藝要求。 - It is also shown that the allowable errors for section dimension are loose and the allowable errors for axis line deviations are suitable in the " code for acceptance of constructional quality of concrect structures " ( gb50204 - 2002 ) . in the fifth chapter : the conclusion and the outlook
統計分析表明， 《混凝土結構工程施工質量驗收規范》 ( gb50204 - 2002 )中關于結構截面尺寸的允許偏差是較寬松的，而對軸線位移的允許偏差基本是合理的。 - Arranging velocity and acceleration sensors simultaneously in the same station , in the identical round of holes , under the condition of the same sample frequency , the differential values of velocities should tally with the actual measurement values of acceleration or be in the range of allowable error
摘要在同一測點同時布置了速度和加速度傳感器，在同一炮次中，在同樣的采樣頻率情況下，速度值求導應該與實測加速度相吻合或在誤差允許范圍內。 - Feedrate planning of continuous micro - line ' s start and end points are discussed , and the constraining conditions , including the machine ' s acceleration and deceleration capability , allowable error of corner machining , maximum acceleration and dynamical behavior of the machine , are established 。
摘要針對連續小直線段高速高精插補算法中起始點和終止點的速度規劃，建立了包含機床加減速性能、轉接處誤差控制、最大加速度以及機床負載功率等的速度約束條件。 - When the silicon technology comes to deep sub - micron level , the interconnect delay exceeds the gate delay ; and because of the increase of 1c work frequency , the allowable errors become smaller , and the influence of the transmission delay gets bigger , which increase the difficulty of the circuit design
在深亞微米制造技術中，芯片互連線延遲超過門延遲，而且隨著集成電路工作頻率的提高，允許的時序容差變小，傳輸延遲的影響加大，設計工作難度增加。 - One of the focuses in this dissertation is the design of a recognition quality evaluator for graph entities . the original image information corresponding to the graph entities is considered as a constrained template or allowable error range . some evaluating factors , defined by using fuzzy theory , have been proposed to express a graph entity ' s recognition quality and as the input of the quality evaluator
本文重點討論了圖素質量評價器的設計，提出采用圖素識別質量特征因子來表述圖素的識別質量，并以矢量圖素對應的光柵圖元作為約束矢量圖素的模板或公差帶，以此提取反映識別質量的特征因子，結合模糊理論的有關概念定義各種特征因子的表達式；圖素的識別質量特征因子作為圖素識別質量評價器的輸入，由評價器經過處理后輸出對圖素識別質量的評判結果。 - Examinations of steady status and analysis of dynamic experiments have been conducted on band - tube evaporator and parallel - flow condenser using r134a refrigerant . the steady examination show that the model error was under the allowable error , the inlet mass and enthalpy disturb experiments indicate that the subsection model , be good at reflecting the change of parameters of the heat exchanger , accord with the basic principle of thermodynamics theory and the actual work status . hence , the subsection simulation model research has important benefits both on theory and engineering application
在進行仿真試驗時，以使用r134a作制冷劑的管帶式蒸發器和平行流式冷凝器為對象，完成了穩態仿真計算、試驗和動態仿真分析，穩態計算結果和試驗數據對比表明，其誤差在允許范圍內；進口質量和焓值的擾動試驗結果表明：本文所建的區段式換熱器仿真模型，能很好的反映換熱器性能參數的動態變化，與系統熱動力學理論和冷凝器、蒸發器的實際工作過程基本一致。